Uncoupling and re-coupling rolling stock problem

Achte bitte darauf, dass Du mit deinem Thema bzw. mit deiner Frage im richtigen Bereich bist.
Die Bereiche sind: Einstellungen im Forum, EEP aktuell ab EEP7 , Splines, Rollmaterialien, Immobilien, Landschaftselemente, Signale und Schaltung, Anlagenvorstellungen, Schnappschüsse Konstrukteure, EEP Treffen , Laberecke, Online - Handbuch EEP Vielen Dank für die Unterstützung das Forum übersichtlich zu halten.
Bilder/Fotos aus dem Internet sind nur als Link gestattet. Eigene Fotos, also Fotos aus dem realen Leben, sind erstens mit Eigenes Bild als Quellenangabe zu kennzeichnen und zweitens nur als Dateianhang im Beitrag zulässig. Bilder ohne Quellenangaben und Bilder dessen Quelle das Internet wie z. B. Google ist, werden gelöscht.
  • SYSTEM

    Win 10 Pro, Processor Intel®Core i5-4690 CPU @ 3.5GHz, RAM 8GB, 54-Bit OS

    EEP 13 Plugins 1 & 2

    Track layout is Single line, two way switch, parallel lines, two way switch, single terminal line

    ---------------\============/--------------|

    E = Engine, W= Wagon, numbers 1, 2 … = Couplings

    I have a problem with coupling rolling stock.

    Train is and engine and two wagons

    Coupling 4 goes from linked to deactivated.

    Vehicle contact set to Speed 2km Release Coupler Rear/Rolling stock 2, Front Coupler Tick, Rear Coupler Tick

    Track layout is Single line, two way switch, parallel lines, two way switch, single terminal line

    ---------------\============/--------------

    6W54W32E1 >>>> Train enters parallel line from left

    6W54W3 2E1 >>>> Engine detaches Coupling 4 Deactivates

    Engine reverses on other line then backs up from the left

    2E1 >>>> 6W54W3 Reversing up to wagons

    <<<<< 2E16W5 4W3 Engine and one Wagon only move away leaving one wagon behind

    What have I failed to do.

    :am_1:

  • Hello,

    If I understood you correctly, the locomotive couples again at the other end and also drives off, but then a car is left standing. Probably you have both directions active in the contact or a time delay built in?

    Hallo,

    wenn ich dich richtig verstanden habe koppelt die Lok wieder am anderen Ende an und fährt auch los, dann wird aber ein Wagen stehen lassen. Vermutlich hast du im Kontakt beide Richtungen aktiv oder eine Zeitverzögerung eingebaut?

    Gruß
    Dieter

    -----------------------------------------------------------------------------------

    Sie haben Lua? :ad_1: Ist das ansteckend?

    Bleibt alle schön EEP-besessen :ae_1:

    Hardeware und Software

    __________________________________________
    EEP alle Versionen ab EEP6 mit allen Plugins,
    Homenos5, Homenos8,...,HomeNos17 DEV...
    Intel I7 4790k 4x 4Ghz, 32 GB RAM, NVidia GTX 1080 ti 11GB, Direct x V11, Windows 10 pro 64 Bit,
    Laptop Medion Erazer, 16GB RAM, 500GB SSD, 2 TB HDD, GT 850 von Nvidia, Windows 10 Home 64bit

  • Hallo,

    ich habe das mit Routen gelöst.

    Wenn der Zug einfährt, hat er die Route "Einfahrt". Nur für diese Route wird die Abkopplung eingestellt. Er erhält nach dem Einfahren die Route "Rangieren". Wenn er mit der Route "Rangieren" wieder an die Wagen heranfährt, wird dann die Abkopplung nicht vorgenommen. Dann bekommt der Zug die Route "Ausfahrt", damit der Wendepunkt der Lok beim Rangieren nicht ausgelöst wird.

    Ich hoffe, dass die Übersetzung verständlich sein wird.

    Hello,

    I have solved this with routes.

    When the train arrives, it has the route "Arrival". The uncoupling is only set for this route. After entering, it receives the route "Shunting". When it approaches the wagons again with the route "Shunting", the uncoupling is not carried out. Then the train gets the route "Exit" so that the turning point of the locomotive is not triggered during shunting.


    I hope that the translation will be understandable.

    Translated with http://www.DeepL.com/Translator (free version)

    Gruß

    ruetzi

    Edit:

    You may have to re-arm couplings that were deactivated during uncoupling. I uncoupled the locomotive (1 from the front) and re-armed both couplings when shunting.

    Eventuell musst Du Kupplungen wieder scharf stellen, die beim Abkuppeln deaktiviert wurden. Ich habe die Lok (1 von vorne) abgekoppelt und beim Rangieren ihre Kupplungen beide wieder scharf gestellt.

    EEP 5, HomeNos 5/8/13/15, EEP 8, 10, 11, 13, 14, 15, EEP 16.4 Expert, Plugin 1
    PC Intel Core i5-4460 QUAD-Core 3.2 GHz, 16 GB PC1600 DDR3-RAM, 250 GB SSD, nVidia GeForce GTX 750Ti - 2 GB DDR5, Windows 8.1
    Notebook Pentium Dual Core 2 GHz, 4 GB DDR3-RAM, Intel GMA3000 Grafik

    EEP - immerhin das Beste vom Schlechten - mit Tendenz zum Besseren!

    Einmal editiert, zuletzt von ruetzi (17. Februar 2021 um 13:04)

  • DH1 and ruetzi,

    Thank you for your feedback. I have taken on board both of your comments.

    I had both directions in contacts set the same.

    I will also set up routes for the actions in future.

    Many thanks

    Code
    Danke für Ihre Rückmeldung. Ich habe Ihre beiden Kommentare berücksichtigt.
    
    Ich hatte beide Richtungen in Kontakten gleich eingestellt.
    
    Ich werde auch in Zukunft Routen für die Aktionen festlegen.
    
    Danke vielmals